Ameristar Kitchen Remodeling Nationwide

Ameristar Kitchen Remodeling: The Los Angeles Owner’s Guide

Ameristar kitchen remodeling in Los Angeles typically runs $16,520-$53,100 for a full project, with cabinet installation, countertop replacement, and island reconfiguration available as standalone services. We stock Ameristar-compatible cabinet hardware, hinge systems, and drawer glide assemblies on our Los Angeles trucks, and we can usually schedule an in-home assessment within 48 hours. Most homeowners realize their Ameristar components are failing when cabinet doors sag, drawers bind, or the soft-close mechanism quits working - often after 8-12 years in the dry, seasonal heat of the Los Angeles basin, which accelerates wear on particleboard substrates and polymer glide components.

Call (213) 652-7670

Which Ameristar Models This Applies To

Ameristar produces cabinet systems across several residential lines, and the parts differ in ways that matter for replacement. The Ameristar Classic series uses a 35mm cup hinge with a 110-degree opening angle and a 3/4-inch overlay standard, while the Ameristar Pro line shifts to a 105-degree hinge with integrated soft-close dampers mounted on a 1/2-inch overlay frame. The drawer box construction varies too: Classic employs a 1/2-inch sides with a stapled butt joint, and Pro uses a 5/8-inch dovetail box with undermount glides rated for 75 pounds. We see the wrong glide ordered about once a month in Los Angeles because a homeowner reads “Ameristar” and misses the series suffix on the interior label.

To identify your part, open the cabinet door and check the hinge cup for a stamped code (usually “AS-35” or “AS-105” followed by a date stamp), or remove the drawer and photograph the glide rail - the part number is laser-etched on the inner rail near the rear bracket. For OEM replacement, we order through Ameristar’s West Coast distribution in City of Industry, which typically delivers to our Los Angeles warehouse in three business days. We also stock quality aftermarket equivalents from Blum and Salice that meet or exceed the original specs at a lower per-unit cost, and we warranty either option under our 365-Day Done Right Promise.

Signs Your Ameristar Kitchen Remodeling Is Failing

• Doors hang crooked or won’t stay closed. The 35mm hinge cup has wallowed out in the particleboard door, or the mounting plate screws have stripped their pilot holes. In Los Angeles, the thermal cycling between 55-degree winter mornings and 85-degree summer afternoons expands and contracts the substrate, loosening the grip over time.
• Drawers stick, jump, or require a tug to open. The polymer glide wheels have flattened or the ball bearings have shed their grease, often from overloading - the Classic line is rated for 50 pounds, and we’ve found drawers holding 80-plus pounds of cast iron in Silver Lake kitchens.
• Soft-close feature quits working or slams shut. The hydraulic damper cartridge inside the hinge or glide has leaked its silicone fluid. This is a sealed unit; it cannot be refilled, only replaced.
• Laminate peeling at edges or seams. The PVA adhesive has failed due to moisture exposure near the sink or steam from a ventless range. Ameristar’s standard laminate is thermofused PVC; delamination means the substrate has swollen and the panel needs replacement, not just re-gluing.
• Island cabinets shifting or countertop cracking. The base cabinet leveling legs have settled into the subfloor, or the island was never anchored to the floor per California seismic code. In Los Angeles, this is a safety issue as much as a cosmetic one.

Before

After

Replacement Cost & What’s Included

The spread on these numbers comes down to three factors: the linear footage of cabinets, the material grade you select, and the condition of what’s behind the existing boxes. A 10×10 kitchen with Ameristar Classic replacement cabinets, quartz countertops, and a simple subway tile backsplash lands near the middle of the full-remodel range. If we open the walls and find galvanized plumbing that needs updating, or if the floor isn’t level within 1/4 inch over 10 feet, the number moves - but not without a signed change order, per Clause 1 of the Haven Standard. Every quote we deliver is a flat written price with line-item detail: cabinets, countertops, demolition, disposal, permits, and final inspection. No work starts until you have that number in hand.

DIY or Call Us?

There’s a clear line between what a homeowner can handle and what requires a licensed contractor in Los Angeles. Swapping a single hinge or a drawer glide is straightforward if you have the exact part number and a cabinet-grade screwdriver - we tell homeowners to bring their old hinge to our office and we’ll match it at no charge. Where DIY goes wrong is in the cumulative tolerances: a door adjusted 1/16 inch too high rubs the frame, a drawer glide mounted 1/32 inch off-square binds, and three misaligned cabinets throw the countertop seam off by half an inch.

More critically, any work involving electrical relocation (moving outlets for a new island configuration), gas line modification for a cooktop, or structural changes to bearing walls requires permits and licensed trades in Los Angeles. We pull those permits, coordinate the inspections, and deliver a documented photo record of every stage - included as standard, not an upgrade. If you’re unsure what’s behind your cabinets, call (213) 652-7670 and we’ll schedule a free assessment. Grant Rowan still does some field visits personally, and he’ll show you exactly what we’re looking at.

FAQs