Unilock Roofing Nationwide

Unilock Roofing: The Los Angeles Owner’s Guide

Unilock roofing components in Los Angeles typically run $470-$2,125 for repair and $9,440-$23,600 for full replacement, with most Unilock-compatible parts available same-day through our network. We stock and install Unilock-matched roofing assemblies across the Los Angeles basin, from Santa Monica to Silver Lake. Most owners discover a Unilock part has failed when they spot water staining on a ceiling after the first real rain, or when a section of coping or flashing lifts in a Santa Ana wind event that the rest of the roof handled fine.

Call (213) 652-7670

Which Unilock Models This Applies To

Unilock’s roofing line breaks into three families: the Estate Wall coping systems, the Brussels Dimensional paver-adjacent drainage assemblies, and the earlier Series 1000 precast concrete roof tiles that shipped from 2003 through 2012. The critical compatibility gotcha is the coping clip spacing: Estate Wall post-2015 uses a 6-inch on-center stainless clip, while pre-2015 units used a 4.5-inch galvanized clip that corrodes faster in Los Angeles marine air. If you’re reading a faded stamp on the underside of a coping unit, look for “U-LA” followed by a two-digit year; anything without that stamp is likely the older Series 1000 and needs the wider clip pattern.

We source OEM Unilock clips and membrane through their Ontario distribution center, though for the Series 1000 tiles that are now discontinued, we spec a quality aftermarket equivalent from Westile in City of Industry. The aftermarket tiles match the 15-5/8-inch module width and the 2-3/8-inch reveal height, but the color batch will vary slightly from original Unilock stock. We photograph the existing field before ordering so you see the match in daylight before we install.

Signs Your Unilock Roofing Is Failing

• Coping stones shift or rock underfoot. The stainless or galvanized clips beneath have either corroded through (common within 8-10 years within three miles of the Pacific) or the mortar bed has de-bonded from thermal cycling. In Los Angeles, the daily 20-degree swing between morning marine layer and afternoon sun accelerates this.
• Water enters at parapet corners but nowhere else. Unilock’s preformed corner pieces use a separate membrane boot that seals with a compression fit; when the EPDM ages past 12 years in UV, the corner becomes the path of least resistance.
• Drainage pavers pond water instead of shedding it. The 1/4-inch-per-foot slope specified in Unilock’s install manual depends on a properly set screed bed. Settling on hillside properties in the Hollywood Hills or Mount Washington often throws this off, and the pavers themselves don’t flex to compensate.
• Efflorescence blooms across the field in streaks. This white mineral deposit signals water is moving through the concrete body rather than across the surface membrane, usually because the secondary drainage plane behind the coping has failed.
• Cracking follows the control joint pattern exactly. When a crack tracks the joint, the coping is expanding against a fixed point, typically because the expansion joint filler was omitted or replaced with rigid mortar during a prior repair.

Before

After

Replacement Cost & What’s Included

Repair of Unilock roofing assemblies in Los Angeles runs $470-$2,125 depending on how many linear feet of coping or how many square feet of drainage field need attention. Full replacement of a Unilock roof system starts at $9,440 and tops out around $23,600 for larger footprints with parapet complexity. The spread comes from three factors: access (scaffold versus swing stage), whether we can match existing color from current stock or need a custom batch, and whether the substrate deck beneath the Unilock needs repair before new membrane goes down.

Every quote is a flat written price with line-item parts and labor, delivered before work starts. Under Clause 1 of the Haven Standard, that number doesn’t change unless the scope changes, and no change proceeds without a signed change order. The work carries our 365-Day Done Right Promise, and you receive a documented photo record of the substrate condition, the new membrane install, and the finished coping placement.

DIY or Call Us?

An owner can safely check three things: whether a coping stone rocks by hand, whether the drain outlets are clear of leaf debris, and whether the corner membrane boots show surface cracking. Do not attempt to lift a coping stone yourself; the units weigh 45-60 pounds each, and the parapet edge is an unforgiving drop. More critically, if water has entered the assembly, the substrate condition is unknown until the field comes up, and walking on a compromised roof deck is how people find the weak spot the hard way.

We stock Unilock-compatible clips, membrane, and corner boots on our Los Angeles service trucks, and we carry the proper parapet harness and anchor points for working at height. If it’s not written down, it didn’t happen, so we document the substrate, the repair, and the finished condition in a photo record you receive before we invoice. Call (213) 652-7670 to schedule your free estimate.

FAQs